summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* Initial version of a SAM7 USART based ISO7816-3 T=0 snifferHarald Welte2010-11-146-2/+529
* enable USB string descriptorsHarald Welte2010-11-141-1/+1
* disable USB EP0 debuggingHarald Welte2010-11-141-1/+1
* Use smaller number of request contexts on a SAM64Harald Welte2010-11-131-0/+5
* On the Olimex board, the buttons are low-activeHarald Welte2010-11-131-1/+7
* AT91SAM7S: Fix linker script (stack) for 64kByte flash versionHarald Welte2010-11-131-1/+1
* mark _ctype as const to be able to put it in flashHarald Welte2010-11-132-2/+2
* add linker scripts for AT91SAM7S64 (64kByte flash / 16kByte RAM) variantHarald Welte2010-11-122-0/+210
* fix STAT_ERR/STAT_IRQ bit definition error in RC632 STATUS register definitionlaforge2008-05-241-2/+2
* Make the diffmiller decoder a __ramfunc. Should severely increase decoder spe...henryk2008-05-222-2/+2
* Switch SSC DMA Tx buffer allocation to dynamic, frees about 16k of RAM (the f...henryk2008-05-221-20/+46
* Add code to change uid/nonce on the flyhenryk2008-04-281-0/+44
* Check received length of the frame that is supposed to contain the PCD challengehenryk2008-04-282-5/+30
* Remove obsolete commandhenryk2008-03-211-20/+0
* Change inf for OpenPICChenryk2008-03-181-6/+6
* Add new hardware revision, make it the defaulthenryk2008-03-183-3/+15
* Print error code in case of errorhenryk2008-03-181-1/+3
* set_nonce functionhenryk2008-03-181-24/+35
* this would be the more correct parity valuehenryk2008-03-181-0/+1
* Scale back the debug outputhenryk2008-03-181-6/+38
* Scale back the debug outputhenryk2008-03-181-1/+1
* Remove performance print, it's blocking the IRQ too long which in turn will m...henryk2008-03-181-0/+2
* Actually use the received data for the decision whether to send anticol frameshenryk2008-03-181-4/+8
* Only set up clocks once in the layer 2a codehenryk2008-03-181-6/+17
* Add dynamic UID, nonce encoding on the flyhenryk2008-03-172-26/+92
* Use diffmiller performance measurement toolshenryk2008-03-171-0/+3
* Add performance measurement toolshenryk2008-03-172-0/+23
* Change used interruptshenryk2008-03-171-2/+1
* Revert since the 'faster' version was not correct (and a fixed version was ev...henryk2008-03-151-4/+5
* Fix the clock gating for the new layer 2 codehenryk2008-03-152-7/+33
* Another 36 carrier cycles (is not fully correct though)henryk2008-03-141-1/+13
* Enhances timing by 14 carrier cycleshenryk2008-03-141-5/+4
* Faked anticollision working now. During stress test (OpenPCD reqa firmware in...henryk2008-03-147-39/+67
* Better Outputhenryk2008-03-142-3/+4
* Add T/C based receiver code with integrated miller decoderhenryk2008-03-1419-132/+400
* Add forgotten sanity checkhenryk2008-03-131-0/+1
* Remove SSC DMA Rx buffers that are not going to be used for now and take up p...henryk2008-03-122-1/+8
* Further optimizations, is now down to 1450 MCK/2 cycles for a 7 bit frame, th...henryk2008-03-101-39/+29
* Further optimisation on the differential miller decoder, is now down to 1750 ...henryk2008-03-102-135/+137
* Add performance measurement codehenryk2008-03-109-65/+276
* Add size printouts before and after compilationhenryk2008-03-091-1/+11
* Fix sendinghenryk2008-03-094-21/+126
* convert pio irq isr to a switching isrhenryk2008-03-054-11/+19
* Port over the differential miller decoder from the sniffonly host toolhenryk2008-03-0515-35/+523
* Copy over the relevant changes from the sniffonly branch pending integrationhenryk2008-03-0511-119/+228
* Forgotten commithenryk2008-03-051-0/+6
* anticol working more often nowhenryk2008-03-042-0/+7
* Pretender does now do anticol. At least in some cases.henryk2008-03-031-47/+48
* Sending seems to be reliable now.henryk2008-03-034-14/+63
* Implement transmissionhenryk2008-03-0310-43/+495
personal git repositories of Harald Welte. Your mileage may vary