openpcd - Firmware for the OpenPCD, OpenPICC and SIMtrace hardware

	Commit message (Collapse)	Author	Age	Files	Lines
*	simtrace: 7816 UART: Add missing entry in Di table	Sylvain Munaut	2012-01-26	1	-1/+1
\| \| \| \| \| \|	Add missing entry in Fi_table. It's apparently used as '64' in some reader and 'unsupported' in some other. For simtrace I guess we should consider it 64.
*	Make sure we don't forward power _and_ supply SIM power at the same time	Kevin Redon	2011-12-18	1	-0/+10
\| \| \| \| \| \| \| \|	The FPF2005 has no reverse voltage blocker, this is why the 3.3V from the LDO flows back into VCC_PHONE. It even damages the chip (so says the datasheet) I corrected the double power source problem by disabling the LDO (see patch), but still 1.8V does not work and 3.0-3.3V is used. I have to look for other reasons.
*	Fix fi/di calculation for certain mobiles like GT-S770 or HTC Raphael	Bjoern Kerler	2011-10-21	1	-3/+3
\| \| \| \| \|	There were some mistakes while copying the tables from ISO 7816-3, and also a quite old version of 7816-3 was used.
*	SIMTRACE: ISO7816: Deal with ATR that don't have historical bytesv0.2	Harald Welte	2011-08-16	1	-11/+21
\| \| \| \| \|	In case there are no historical bytes, we immediately transition from the last TD byte into the WAIT_TCK or WAIT_APDU state.
*	ISO7816: Properly handle T=0 only cards without TCK in ATR	Harald Welte	2011-08-16	1	-1/+13
\|
*	SIMTRACE UART: Reset error status on error related IRQ	Harald Welte	2011-08-15	1	-0/+9
\| \| \| \| \|	This prevents an IRQ-flood after a parity or overrun error, which in turn would cause a watchdog reset.
*	simtrace UART: set INACK flag to make sure we ignore any parity error	Harald Welte	2011-08-15	1	-3/+3
\| \| \| \| \| \| \|	As a SIM card tracer, we want to remain completely passive and thus not signal back parity errors with the ISO 7816 NACK. The UART INACK flag does exactly that...
*	DFU: add third 'alternate configuration' for RAM load	Harald Welte	2011-07-30	2	-0/+2
\| \| \| \| \|	This will allow us to load code directly into RAM without going through flash.
*	simtrace: add some early spi flash utility routines	Harald Welte	2011-07-30	2	-0/+224
\| \| \| \|	This also adds a new 'main_factory' target for simtrace
*	simtrace: initialize sniffer mode right after start-up	Harald Welte	2011-06-30	1	-18/+22
\|
*	simtrace: switch VCC_SIM into output mode, as we use it to supply Vcc	Harald Welte	2011-06-21	1	-2/+8
\| \| \| \| \| \|	This is just a temp rework in the 1st generation prototype, as the bus switch has too high resistance for passing throuhg Vcc from the phone to the SIM.
*	simtrace: add VCC_PHINE IRQ detection	Harald Welte	2011-06-21	1	-0/+19
\|
*	simtrace: introduce mode sniffer / mitm switching	Harald Welte	2011-06-17	2	-6/+50
\|
*	simtrace: add support for the analog bus switch	Harald Welte	2011-06-16	3	-1/+93
\|
*	update USB strings (company name and some copy+paste mistakes)	Harald Welte	2011-06-15	2	-3/+3
\|
*	typo: Fix typo, transform reqyests to requests.	Holger Hans Peter Freyther	2011-01-31	1	-1/+1
\|
*	add missing usb_strings_dfu.txt file to simtrace directory	Harald Welte	2010-12-09	1	-0/+5
\|
*	simtrace: Make sure ATR is sent in its own RCTX and we re-allocate in time	Harald Welte	2010-11-21	1	-1/+11
\|
*	simtrace: fix problems causing bogus waiting time expirations	Harald Welte	2010-11-18	1	-1/+5
\|
*	simtrace: Introduce code for proper handling of PTS / PPS	Harald Welte	2010-11-18	1	-12/+148
\|
*	simtrace: add TC based waiting time counter, signal ATR / expiry via USB	Harald Welte	2010-11-18	5	-78/+292
\|
*	simtrace: introduce RST pin handling	Harald Welte	2010-11-14	1	-12/+32
\|
*	Initial version of a SAM7 USART based ISO7816-3 T=0 sniffer	Harald Welte	2010-11-14	3	-0/+503