From ea1423e7c9aa7da9e1017d71d8887a0b736db81e Mon Sep 17 00:00:00 2001 From: laforge Date: Mon, 16 Oct 2006 16:37:59 +0000 Subject: add some bits and pieces of documentation git-svn-id: https://svn.openpcd.org:2342/trunk@272 6dc7ffe9-61d6-0310-9af1-9938baff3ed1 --- doc/common-usbproto.xml | 190 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 190 insertions(+) create mode 100644 doc/common-usbproto.xml (limited to 'doc/common-usbproto.xml') diff --git a/doc/common-usbproto.xml b/doc/common-usbproto.xml new file mode 100644 index 0000000..3b8b894 --- /dev/null +++ b/doc/common-usbproto.xml @@ -0,0 +1,190 @@ +
+USB Protocol + +The USB protocol is completely non-standard. Since OpenPICC is a very +special-purpose device, it's obvious that no standard USB protocol will be +applicable. However, our vendor-specific protocol is completely open and +documented to allow for development of interoperable applications. + + +
+USB Endpoints + +Since the SAM7 hardware only provides four USB endpoints, we have to use them +according to their endpoint type, rather than to their function within the +protocol. We have to overload and (de)multiplex within one endpoint quite a +bit. + + +EP0 - Control Endpoint +EP1 - Bulk Out endpoint (host -> device) +EP2 - Bulik In endpoint (device -> host) +EP3 - Interrupt In endpoint (device -> host) + + +The control endpoint behaves according to the USB specification. It only +takes care of usb configuration and management. No application data is +transferred over it. + +
+ +
+USB packets, transfers + +In order to understand this devices' USB prootocol, some basics about any +communication with USB endpoints need to be known. + + +USB endpoints exchange a stream of data by means of USB transfers. Every +transfer is conveyed as multiple transaction. Every transaction transports +multiple USB packets. The Endpoint buffer size of the SAM7 usb device +controller is 64bytes for EP1, EP2 and EP3. Therefore, a single packet can be +up to 64 bytes in size. As soon as a packet smaller than the endpoint size +(64byte) is received, the end of that particular USB transfer is detected. +If the transfer size is an integral size of the endpoint size, a zero-length-packet (ZLP) is sent to explicitly signal the end of the transfer. + + +The buffer management inside the SAM7 firmware can deal with USB transfers of +up to 2048 bytes in size. To optimize memory efficiency, all buffers are +statically pre-allocated, and the majority of USB buffers is only 64bytes in +size. This way, the memory consumption for small transfers (such as register read/write transfers) can be kept low. + + +Large transfers (> 64 bytes, but &let; 2024 bytes) should be used only +when they are absolutely required. + +
+ +
+Host software interaction with USB Endpoints + +Any host software operating the USB device should take into consideration +that memory is a scarce resource on the SAM7, especially for +applications with relatively high speed compared to the USB 1.1 full speed bandwith), such as higher-bitrate 847kHz ISO14443 communication. + + +Therefore it is important to serve device requests on the BULK IN and +INTERRUPT IN endpoints as soon as possible. In most cases, the application +will simply keep those two pipes open all the time, by re-submitting an USB +request block as soon as the previous one at that endpiont has completed. + + +The BULK OUT endpoint will obviously only be filled with requests from the +host software when there are any such requests. + + +On the highest level of the protocol, there are three different classes of device requests: + + +1. uni-directional without high-level acknowledgement, such as a register +write without explicit request for a response. This means that the host +software will only send a single BULK OUT transfer. This transfer is +acknowledged inherently by the USB protocol, and the host software can be sure +that the transfer was correctly received by the device. + + +2. bi-directional with a single response, such as a register read. This means +that the host sends a single BULK OUT transfer, to which the device replies +with a single BULK IN transfer. + + +3. bi-directional with multiple responses. This means that even though the +host only sends a single BULK OUT transfer, there will be multiple BULK IN +transfers in response. + +
+ +
+The usb transfer header + +Application data transferred over EP1, EP2 and EP3 is prefixed with a +four-byte header, 'struct openpcd_hdr'. + + +The first byte is the command byte. The high nibble of the command byte +specifies the command class, whereas the the low nibble selects the particular +command within a given class. + + +The second byte specifies flags. There are currently two flags: + + +The RESPOND flag signifies that the sender of this transfer explicitly +requests a response back from the other side. + + +The ERROR flag signifies that this transfer indicates some error + + +The MULTIPLE flag signifies that this is part of a response that consists of +multiple transfers. + + +The LAST flag signifies that the current transfer is the last transfer +of a multiple-transfer response. + + +The third byte is called 'register' for historical purpose. It should +actually rather be called address or index. Its significance differs +according to the actual command that is being performed. + + +The fourth byte is called 'val' for 'value'. Again, its purpose is command +specific. In case of e.g. a register write, it is the value to be written +into the register. + +
+ +
+The individual USB protocol commands + +
+Generic USB commands: CMD_CLS_GENERIC + +
+CMD_GET_VERSION + +This command is used to obtain the version number of the USB device. This +might be used to differentiate different hardware revisions by the host software. + + +The response to this command contains the version number in the +variable-length 'data' section of the transfer. + +
+ +
+CMD_SET_LED + +Using this command, the host software can control the LED's present in the +OpenPICC. The LED can be specified in the 'reg' section of the header. +Currently there are two LED's, LED 1 (green) and LED 2 (red). The 'val' +header field controls whether the LED should be switched on (1) or off (0). + +
+ +
+CMD_GET_SERIAL + +This command is used to obtain the serial number of the OpenPICC device. +The serial number is returned in the 'data' section of the response transfer. + +
+ +
+ +
+USB Testing commands +
+CMD_USBTEST_IN + + +
+
+CMD_USBTEST_OUT + + +
+
+ + -- cgit v1.2.3