1 files changed, 114 insertions, 0 deletions
diff --git a/peripherals/dbgu/dbgu.c b/peripherals/dbgu/dbgu.c
new file mode 100644
index 0000000..0b3b380
--- /dev/null
+++ b/peripherals/dbgu/dbgu.c
@@ -0,0 +1,114 @@
+/* ----------------------------------------------------------------------------
+ *         ATMEL Microcontroller Software Support 
+ * ----------------------------------------------------------------------------
+ * Copyright (c) 2008, Atmel Corporation
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * - Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the disclaimer below.
+ *
+ * Atmel's name may not be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
+ * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
+ * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * ----------------------------------------------------------------------------
+ */
+
+//------------------------------------------------------------------------------
+//         Headers
+//------------------------------------------------------------------------------
+
+#include "dbgu.h"
+#include <board.h>
+
+//------------------------------------------------------------------------------
+//         Global functions
+//------------------------------------------------------------------------------
+//------------------------------------------------------------------------------
+/// Initializes the DBGU with the given parameters, and enables both the
+/// transmitter and the receiver. The mode parameter contains the value of the
+/// DBGU_MR register.
+/// Value DBGU_STANDARD can be used for mode to get the most common configuration
+/// (i.e. aysnchronous, 8bits, no parity, 1 stop bit, no flow control).
+/// \param mode  Operating mode to configure.
+/// \param baudrate  Desired baudrate (e.g. 115200).
+/// \param mck  Frequency of the system master clock in Hz.
+//------------------------------------------------------------------------------
+void DBGU_Configure(
+    unsigned int mode,
+    unsigned int baudrate,
+    unsigned int mck)
+{
+    #if defined(cortexm3)
+    // Enable clock for UART
+    AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_DBGU);
+    #endif
+
+    // Reset & disable receiver and transmitter, disable interrupts
+    AT91C_BASE_DBGU->DBGU_CR = AT91C_US_RSTRX | AT91C_US_RSTTX;
+    AT91C_BASE_DBGU->DBGU_IDR = 0xFFFFFFFF;
+    
+    // Configure baud rate
+    AT91C_BASE_DBGU->DBGU_BRGR = mck / (baudrate * 16);
+    
+    // Configure mode register
+    AT91C_BASE_DBGU->DBGU_MR = mode;
+    
+    // Disable DMA channel
+    AT91C_BASE_DBGU->DBGU_PTCR = AT91C_PDC_RXTDIS | AT91C_PDC_TXTDIS;
+
+    // Enable receiver and transmitter
+    AT91C_BASE_DBGU->DBGU_CR = AT91C_US_RXEN | AT91C_US_TXEN;
+}
+
+//------------------------------------------------------------------------------
+/// Outputs a character on the DBGU line.
+/// \note This function is synchronous (i.e. uses polling).
+/// \param c  Character to send.
+//------------------------------------------------------------------------------
+void DBGU_PutChar(unsigned char c)
+{
+    // Wait for the transmitter to be ready
+    while ((AT91C_BASE_DBGU->DBGU_CSR & AT91C_US_TXEMPTY) == 0);
+    
+    // Send character
+    AT91C_BASE_DBGU->DBGU_THR = c;
+    
+    // Wait for the transfer to complete
+    while ((AT91C_BASE_DBGU->DBGU_CSR & AT91C_US_TXEMPTY) == 0);
+}
+
+//------------------------------------------------------------------------------
+/// Return 1 if a character can be read in DBGU
+//------------------------------------------------------------------------------
+unsigned int DBGU_IsRxReady()
+{
+    return (AT91C_BASE_DBGU->DBGU_CSR & AT91C_US_RXRDY);
+}
+
+//------------------------------------------------------------------------------
+/// Reads and returns a character from the DBGU.
+/// \note This function is synchronous (i.e. uses polling).
+/// \return Character received.
+//------------------------------------------------------------------------------
+unsigned char DBGU_GetChar(void)
+{
+    while ((AT91C_BASE_DBGU->DBGU_CSR & AT91C_US_RXRDY) == 0);
+    return AT91C_BASE_DBGU->DBGU_RHR;
+}
+
+
+