1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
|
/* ----------------------------------------------------------------------------
* ATMEL Microcontroller Software Support
* ----------------------------------------------------------------------------
* Copyright (c) 2008, Atmel Corporation
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* - Redistributions of source code must retain the above copyright notice,
* this list of conditions and the disclaimer below.
*
* Atmel's name may not be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* ----------------------------------------------------------------------------
*/
//------------------------------------------------------------------------------
/// \unit
///
/// !!!Purpose
///
/// The INTERL %norflash Low-level driver code implement procedures to program
/// basic operations described INTEL-specified command set flash devices.
/// The various commands recognized by the devices are listed in the Commands
/// Tables provided in the corresponding INTEL command set compatible flash
/// datasheets. All operation functions are blocked, they wait for the
/// completion of an operation by polling the status register.
///
/// !!!Usage
/// -# Flash program using INTEL_Write_Data().
/// - The Program command is used to modify the data stored at the
/// specified device address. Programming can only change bits
/// from ¡®1¡¯ to ¡®0¡¯. It may be necessary to erase the block before
/// programming to addresses within it. Programming modifies a single
/// Word at a time using static function intel_Program(). Programming
/// larger amounts of data must be done in one Word at a time by
/// giving a Program command, waiting for the command to complete,
/// giving the next Program command and so on.
/// -# erase a block within the flash using INTEL_EraseSector().
/// - Flash erase is performed on a block basis. An entire block is
/// erased each time an erase command sequence is given.
/// -# erase whole blocks within the flash using INTEL_EraseChip().
/// -# INTEL_Reset() function can be issued, between Bus Write cycles
/// before the start of a program or erase operation, to return the
/// device to read mode.
/// -# INTEL_ReadDeviceID() is used to retrieve information
/// about the Flash Device type.
/// -# INTEL_ReadManufactoryId() is used to retrieve information
/// about the Flash Device Manufactory ID.
//------------------------------------------------------------------------------
#ifndef NORFLASHINTEL_H
#define NORFLASHINTEL_H
//------------------------------------------------------------------------------
// Local functions
//------------------------------------------------------------------------------
void INTEL_Reset(struct NorFlashInfo *pNorFlashInfo, unsigned int address);
unsigned int INTEL_ReadManufactoryId(struct NorFlashInfo *NorFlashInfo);
unsigned int INTEL_ReadDeviceID(struct NorFlashInfo *pNorFlashInfo);
unsigned char INTEL_EraseSector(
struct NorFlashInfo *NorFlashInfo,
unsigned int sectorAddr);
unsigned char INTEL_EraseChip(struct NorFlashInfo *NorFlashInfo);
unsigned char INTEL_Write_Data(
struct NorFlashInfo *NorFlashInfo,
unsigned int address,
unsigned char *buffer,
unsigned int size);
const struct NorFlashOperations intelOperations = {
INTEL_Reset,
INTEL_Write_Data,
INTEL_ReadManufactoryId,
INTEL_ReadDeviceID,
INTEL_EraseChip,
INTEL_EraseSector
};
#endif //#ifndef NORFLASHINTEL_H
|
