1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
/* ----------------------------------------------------------------------------
* ATMEL Microcontroller Software Support
* ----------------------------------------------------------------------------
* Copyright (c) 2008, Atmel Corporation
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* - Redistributions of source code must retain the above copyright notice,
* this list of conditions and the disclaimer below.
*
* Atmel's name may not be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* ----------------------------------------------------------------------------
*/
//------------------------------------------------------------------------------
// Headers
//------------------------------------------------------------------------------
#include "aic.h"
#include <board.h>
//------------------------------------------------------------------------------
// Global functions
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
/// Configures an interrupt in the AIC. The interrupt is identified by its
/// source (AT91C_ID_xxx) and is configured to use the specified mode and
/// interrupt handler function. Mode is the value that will be put in AIC_SMRx
/// and the function address will be set in AIC_SVRx.
/// The interrupt is disabled before configuration, so it is useless
/// to do it before calling this function. When AIC_ConfigureIT returns, the
/// interrupt will always be disabled and cleared; it must be enabled by a
/// call to AIC_EnableIT().
/// \param source Interrupt source to configure.
/// \param mode Triggering mode and priority of the interrupt.
/// \param handler Interrupt handler function.
//------------------------------------------------------------------------------
void AIC_ConfigureIT(
unsigned int source,
unsigned int mode,
void (*handler)(void))
{
// Disable the interrupt first
AT91C_BASE_AIC->AIC_IDCR = 1 << source;
// Configure mode and handler
AT91C_BASE_AIC->AIC_SMR[source] = mode;
AT91C_BASE_AIC->AIC_SVR[source] = (unsigned int) handler;
// Clear interrupt
AT91C_BASE_AIC->AIC_ICCR = 1 << source;
}
//------------------------------------------------------------------------------
/// Enables interrupts coming from the given (unique) source (AT91C_ID_xxx).
/// \param source Interrupt source to enable.
//------------------------------------------------------------------------------
void AIC_EnableIT(unsigned int source)
{
AT91C_BASE_AIC->AIC_IECR = 1 << source;
}
//------------------------------------------------------------------------------
/// Disables interrupts coming from the given (unique) source (AT91C_ID_xxx).
/// \param source Interrupt source to enable.
//------------------------------------------------------------------------------
void AIC_DisableIT(unsigned int source)
{
AT91C_BASE_AIC->AIC_IDCR = 1 << source;
}
|
