import basic-ssc-i2s-wm8731-project from at91sam3-ek

ported to at91lib-1.9

1 files changed, 164 insertions, 0 deletions

diff --git a/basic-ssc-i2s-wm8731-project/fatfs_config.h b/basic-ssc-i2s-wm8731-project/fatfs_config.h
new file mode 100644
index 0000000..41a60bf
--- /dev/null
+++ b/basic-ssc-i2s-wm8731-project/fatfs_config.h
@@ -0,0 +1,164 @@
+/* ----------------------------------------------------------------------------

+ *         ATMEL Microcontroller Software Support 

+ * ----------------------------------------------------------------------------

+ * Copyright (c) 2008, Atmel Corporation

+ *

+ * All rights reserved.

+ *

+ * Redistribution and use in source and binary forms, with or without

+ * modification, are permitted provided that the following conditions are met:

+ *

+ * - Redistributions of source code must retain the above copyright notice,

+ * this list of conditions and the disclaimer below.

+ *

+ * Atmel's name may not be used to endorse or promote products derived from

+ * this software without specific prior written permission.

+ *

+ * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR

+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE

+ * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,

+ * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

+ * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

+ * ----------------------------------------------------------------------------

+ */

+

+#ifndef FATFS_CONFIG_H

+#define FATFS_CONFIG_H

+

+//------------------------------------------------------------------------------

+//      General Definitions (previously in ff.h)

+//------------------------------------------------------------------------------

+

+#define	_FATFS_TINY 1

+/* When _FATFS_TINY is set to 1, fatfs is compiled in Tiny mode

+/ Else, it is compiled in normal mode 

+/ Tiny FatFs feature : Very low memory consumption, suitable for small memory 

+/ system. (1KB RAM) : Supports only single drive, no disk format, 

+/ only read functions, no write functions */

+

+//------------------------------------------------------------------------------

+//      Definitions for normal FATFS (previously in ff.h)

+//------------------------------------------------------------------------------

+

+#if _FATFS_TINY == 0

+

+#define _MCU_ENDIAN		2

+/* The _MCU_ENDIAN defines which access method is used to the FAT structure.

+/  1: Enable word access.

+/  2: Disable word access and use byte-by-byte access instead.

+/  When the architectural byte order of the MCU is big-endian and/or address

+/  miss-aligned access results incorrect behavior, the _MCU_ENDIAN must be set to 2.

+/  If it is not the case, it can also be set to 1 for good code efficiency. */

+

+#define _FS_READONLY	0

+/* Setting _FS_READONLY to 1 defines read only configuration. This removes

+/  writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,

+/  f_truncate and useless f_getfree. */

+

+#define _FS_MINIMIZE	0

+/* The _FS_MINIMIZE option defines minimization level to remove some functions.

+/  0: Full function.

+/  1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename are removed.

+/  2: f_opendir and f_readdir are removed in addition to level 1.

+/  3: f_lseek is removed in addition to level 2. */

+

+#define	_USE_STRFUNC	0

+/* To enable string functions, set _USE_STRFUNC to 1 or 2. */

+

+#define _USE_FSINFO	1

+/* To enable FSInfo support on FAT32 volume, set _USE_FSINFO to 1. */

+

+#define	_USE_SJIS	1

+/* When _USE_SJIS is set to 1, Shift-JIS code transparency is enabled, otherwise

+/  only US-ASCII(7bit) code can be accepted as file/directory name. */

+

+#define	_USE_NTFLAG	1

+/* When _USE_NTFLAG is set to 1, upper/lower case of the file name is preserved.

+/  Note that the files are always accessed in case insensitive. */

+

+#define	_USE_MKFS	1

+/* When _USE_MKFS is set to 1 and _FS_READONLY is set to 0, f_mkfs function is

+/  enabled. */

+

+#define _DRIVES		2

+/* Number of logical drives to be used. This affects the size of internal table. */

+

+#define	_MULTI_PARTITION	0

+/* When _MULTI_PARTITION is set to 0, each logical drive is bound to same

+/  physical drive number and can mount only 1st primaly partition. When it is

+/  set to 1, each logical drive can mount a partition listed in Drives[]. */

+

+//------------------------------------------------------------------------------

+//      Definitions for normal FATFS TINY (previously in tff.h)

+//------------------------------------------------------------------------------

+

+#else

+

+#define _MCU_ENDIAN		2

+/* The _MCU_ENDIAN defines which access method is used to the FAT structure.

+/  1: Enable word access.

+/  2: Disable word access and use byte-by-byte access instead.

+/  When the architectural byte order of the MCU is big-endian and/or address

+/  miss-aligned access results incorrect behavior, the _MCU_ENDIAN must be set to 2.

+/  If it is not the case, it can also be set to 1 for good code efficiency. */

+

+#define _FS_READONLY	1

+/* Setting _FS_READONLY to 1 defines read only configuration. This removes

+/  writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,

+/  f_truncate, f_getfree and internal writing codes. */

+

+#define _FS_MINIMIZE	0

+/* The _FS_MINIMIZE option defines minimization level to remove some functions.

+/  0: Full function.

+/  1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename are removed.

+/  2: f_opendir and f_readdir are removed in addition to level 1.

+/  3: f_lseek is removed in addition to level 2. */

+

+#define	_USE_STRFUNC	0

+/* To enable string functions, set _USE_STRFUNC to 1 or 2. */

+

+#define _USE_FSINFO	1

+/* To enable FSInfo support on FAT32 volume, set _USE_FSINFO to 1. */

+

+#define	_USE_SJIS	1

+/* When _USE_SJIS is set to 1, Shift-JIS code transparency is enabled, otherwise

+/  only US-ASCII(7bit) code can be accepted as file/directory name. */

+

+#define	_USE_NTFLAG	1

+/* When _USE_NTFLAG is set to 1, upper/lower case of the file name is preserved.

+/  Note that the files are always accessed in case insensitive. */

+

+#define	_USE_FORWARD	0

+/* To enable f_forward function, set _USE_FORWARD to 1. */

+

+#define _FAT32	1

+/* To enable FAT32 support in addition of FAT12/16, set _FAT32 to 1. */

+

+#endif

+

+//------------------------------------------------------------------------------

+//      Other definitions

+//------------------------------------------------------------------------------

+

+/*-----------------------------------------------------------------------*/

+/* Correspondence between drive number and physical drive                */

+/* Note that Tiny-FatFs supports only single drive and always            */

+/* accesses drive number 0.                                              */

+

+#define DRV_MMC          0

+#define DRV_SDRAM        1

+#define DRV_ATA          2

+#define DRV_USB          3

+#define DRV_NAND         4

+

+

+#define SECTOR_SIZE_DEFAULT 512

+#define SECTOR_SIZE_SDRAM  512

+#define SECTOR_SIZE_SDCARD 512

+

+#endif // FATFS_CONFIG_H