1 files changed, 164 insertions, 0 deletions
diff --git a/basic-ssc-i2s-wm8731-project/fatfs_config.h b/basic-ssc-i2s-wm8731-project/fatfs_config.h
new file mode 100644
index 0000000..41a60bf
--- /dev/null
+++ b/basic-ssc-i2s-wm8731-project/fatfs_config.h
@@ -0,0 +1,164 @@
+/* ----------------------------------------------------------------------------
+ *         ATMEL Microcontroller Software Support 
+ * ----------------------------------------------------------------------------
+ * Copyright (c) 2008, Atmel Corporation
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * - Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the disclaimer below.
+ *
+ * Atmel's name may not be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
+ * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
+ * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * ----------------------------------------------------------------------------
+ */
+
+#ifndef FATFS_CONFIG_H
+#define FATFS_CONFIG_H
+
+//------------------------------------------------------------------------------
+//      General Definitions (previously in ff.h)
+//------------------------------------------------------------------------------
+
+#define	_FATFS_TINY 1
+/* When _FATFS_TINY is set to 1, fatfs is compiled in Tiny mode
+/ Else, it is compiled in normal mode 
+/ Tiny FatFs feature : Very low memory consumption, suitable for small memory 
+/ system. (1KB RAM) : Supports only single drive, no disk format, 
+/ only read functions, no write functions */
+
+//------------------------------------------------------------------------------
+//      Definitions for normal FATFS (previously in ff.h)
+//------------------------------------------------------------------------------
+
+#if _FATFS_TINY == 0
+
+#define _MCU_ENDIAN		2
+/* The _MCU_ENDIAN defines which access method is used to the FAT structure.
+/  1: Enable word access.
+/  2: Disable word access and use byte-by-byte access instead.
+/  When the architectural byte order of the MCU is big-endian and/or address
+/  miss-aligned access results incorrect behavior, the _MCU_ENDIAN must be set to 2.
+/  If it is not the case, it can also be set to 1 for good code efficiency. */
+
+#define _FS_READONLY	0
+/* Setting _FS_READONLY to 1 defines read only configuration. This removes
+/  writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,
+/  f_truncate and useless f_getfree. */
+
+#define _FS_MINIMIZE	0
+/* The _FS_MINIMIZE option defines minimization level to remove some functions.
+/  0: Full function.
+/  1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename are removed.
+/  2: f_opendir and f_readdir are removed in addition to level 1.
+/  3: f_lseek is removed in addition to level 2. */
+
+#define	_USE_STRFUNC	0
+/* To enable string functions, set _USE_STRFUNC to 1 or 2. */
+
+#define _USE_FSINFO	1
+/* To enable FSInfo support on FAT32 volume, set _USE_FSINFO to 1. */
+
+#define	_USE_SJIS	1
+/* When _USE_SJIS is set to 1, Shift-JIS code transparency is enabled, otherwise
+/  only US-ASCII(7bit) code can be accepted as file/directory name. */
+
+#define	_USE_NTFLAG	1
+/* When _USE_NTFLAG is set to 1, upper/lower case of the file name is preserved.
+/  Note that the files are always accessed in case insensitive. */
+
+#define	_USE_MKFS	1
+/* When _USE_MKFS is set to 1 and _FS_READONLY is set to 0, f_mkfs function is
+/  enabled. */
+
+#define _DRIVES		2
+/* Number of logical drives to be used. This affects the size of internal table. */
+
+#define	_MULTI_PARTITION	0
+/* When _MULTI_PARTITION is set to 0, each logical drive is bound to same
+/  physical drive number and can mount only 1st primaly partition. When it is
+/  set to 1, each logical drive can mount a partition listed in Drives[]. */
+
+//------------------------------------------------------------------------------
+//      Definitions for normal FATFS TINY (previously in tff.h)
+//------------------------------------------------------------------------------
+
+#else
+
+#define _MCU_ENDIAN		2
+/* The _MCU_ENDIAN defines which access method is used to the FAT structure.
+/  1: Enable word access.
+/  2: Disable word access and use byte-by-byte access instead.
+/  When the architectural byte order of the MCU is big-endian and/or address
+/  miss-aligned access results incorrect behavior, the _MCU_ENDIAN must be set to 2.
+/  If it is not the case, it can also be set to 1 for good code efficiency. */
+
+#define _FS_READONLY	1
+/* Setting _FS_READONLY to 1 defines read only configuration. This removes
+/  writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,
+/  f_truncate, f_getfree and internal writing codes. */
+
+#define _FS_MINIMIZE	0
+/* The _FS_MINIMIZE option defines minimization level to remove some functions.
+/  0: Full function.
+/  1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename are removed.
+/  2: f_opendir and f_readdir are removed in addition to level 1.
+/  3: f_lseek is removed in addition to level 2. */
+
+#define	_USE_STRFUNC	0
+/* To enable string functions, set _USE_STRFUNC to 1 or 2. */
+
+#define _USE_FSINFO	1
+/* To enable FSInfo support on FAT32 volume, set _USE_FSINFO to 1. */
+
+#define	_USE_SJIS	1
+/* When _USE_SJIS is set to 1, Shift-JIS code transparency is enabled, otherwise
+/  only US-ASCII(7bit) code can be accepted as file/directory name. */
+
+#define	_USE_NTFLAG	1
+/* When _USE_NTFLAG is set to 1, upper/lower case of the file name is preserved.
+/  Note that the files are always accessed in case insensitive. */
+
+#define	_USE_FORWARD	0
+/* To enable f_forward function, set _USE_FORWARD to 1. */
+
+#define _FAT32	1
+/* To enable FAT32 support in addition of FAT12/16, set _FAT32 to 1. */
+
+#endif
+
+//------------------------------------------------------------------------------
+//      Other definitions
+//------------------------------------------------------------------------------
+
+/*-----------------------------------------------------------------------*/
+/* Correspondence between drive number and physical drive                */
+/* Note that Tiny-FatFs supports only single drive and always            */
+/* accesses drive number 0.                                              */
+
+#define DRV_MMC          0
+#define DRV_SDRAM        1
+#define DRV_ATA          2
+#define DRV_USB          3
+#define DRV_NAND         4
+
+
+#define SECTOR_SIZE_DEFAULT 512
+#define SECTOR_SIZE_SDRAM  512
+#define SECTOR_SIZE_SDCARD 512
+
+#endif // FATFS_CONFIG_H